Tukkonen Posted March 14, 2023 Posted March 14, 2023 2.60b:llä tuleeko sulla muilla servuilla sitä nykimistä? Jos ei niin kokeile kopioida jonku muun modin cfg tiedosto tuonne legacy modiin. Quote
Masa_1964 Posted March 14, 2023 Author Posted March 14, 2023 (edited) I'll consider installing it In the mean time I think I found one problem/miss configuration. I now have taken trilinear opti off and also treaded opti off in Nvidia crtl panel. Maybe some graphics driver update has overwritten those in some point. Now I took those off and I think it was bit better. I did have it also in silent a bit and of cause in beg1 but not sure if it was just cause ping. NQ did work pretty much okay. Edited March 14, 2023 by Masa_1964 1 Quote
ASBO Posted March 27, 2023 Posted March 27, 2023 FYI Everyone who has an nvidia card make sure that you go to the control panel - 3d settings/programs/etlegacy - and turn off threaded optimisation in there for the game The open source idtech3 engine that ET legacy uses isnt properly threaded so it causes a few different issues when you have it on Told to me by one of the devs 3 Quote
HarryAimpotter Posted March 28, 2023 Posted March 28, 2023 I tested this with timedemo. On my system the differnce in preformance is about 50%. Average fps 450 vs 300. Quote
Snuffs99 Posted March 28, 2023 Posted March 28, 2023 5 hours ago, HarryAimpotter said: I tested this with timedemo. On my system the differnce in preformance is about 50%. Average fps 450 vs 300. Is that a difference of +50 or -50 mate? (+being better obv) Quote
HarryAimpotter Posted March 28, 2023 Posted March 28, 2023 Turning threaded optimization off gives +50% more fps. 1 1 Quote
Masa_1964 Posted April 8, 2023 Author Posted April 8, 2023 (edited) Question, If I connect to FA ETL server I get much more wide selection on menu section to adjust properties but when connecting fex NQ1 it says at it runs etl but menus are still the same nq1 type? Other thing is at clearly I get 5-7% accuracy loss in NQ1 compared to earlier 2.60b, normaly its been 30-32%, Now I get average 25-26. Its bit better in that FA ETL server but need to aim bit side to get hits, but still hard to get over 30%. So its way too hard to play when half of players get above 40 and 4-5 players gets 50. Its clearly to see in close combats, have some delay (frame skipping?) and impossible to hit anyting. From long distance its okay. Ping does not been changed during time. Edited April 8, 2023 by Masa_1964 Quote
TomekKromek Posted April 8, 2023 Posted April 8, 2023 6 minutes ago, Masa_1964 said: Question, If I connect to FA ETL server I get much more wide selection on menu section to adjust properties but when connecting fex NQ1 it says at it runs etl but menus are still the same nq1 type? You need to differentiate between ETL and ETL mod. We run ETL + ETL mod on Legacy and ETL + NQ on NQ1. The mentioned changes are in the mod. Quote
Masa_1964 Posted April 8, 2023 Author Posted April 8, 2023 (edited) 8 minutes ago, TomekKromek said: You need to differentiate between ETL and ETL mod. We run ETL + ETL mod on Legacy and ETL + NQ on NQ1. The mentioned changes are in the mod. Yeah thats what I ment, I still run both with my 2.60b client so how does it differentiate? I have no problems in jay or silent mods with accuracy. Edited April 8, 2023 by Masa_1964 Quote
Platinum VIP -=HipKat=- Posted April 8, 2023 Platinum VIP Posted April 8, 2023 5 hours ago, Masa_1964 said: Question, If I connect to FA ETL server I get much more wide selection on menu section to adjust properties but when connecting fex NQ1 it says at it runs etl but menus are still the same nq1 type? Other thing is at clearly I get 5-7% accuracy loss in NQ1 compared to earlier 2.60b, normaly its been 30-32%, Now I get average 25-26. Its bit better in that FA ETL server but need to aim bit side to get hits, but still hard to get over 30%. So its way too hard to play when half of players get above 40 and 4-5 players gets 50. Its clearly to see in close combats, have some delay (frame skipping?) and impossible to hit anyting. From long distance its okay. Ping does not been changed during time. Maybe this is my problem from here? Same thing, too with long range. I have better success from far away than up close Quote
Masa_1964 Posted April 9, 2023 Author Posted April 9, 2023 Thats exactly what I have, delay from mouse pressing. Its not much but just barely noticeably and critical in close combats. I have some fade memory having that issue long time ago and it was solved, cant remeber what it was. Quote
captnconcrete Posted April 9, 2023 Posted April 9, 2023 (edited) in_mouse "3" in_restart Edited April 9, 2023 by captnconcrete Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.